ANYCUBIC Photon Mono 2 4 Review: Specs, Pros and Cons
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This anycubic fep film 2pcs photon review covers the replacement consumable for your resin printer. The package includes two FEP release films designed for the Photon Mono 2 and Mono 4 series. These films measure 6.3 inches in width and 8.66 inches in length, with a height of 0.75 inches. The integrated design includes a ring for quick installation. You do not need to disassemble the ring or cut the film yourself. Regular replacement helps maintain print quality, as the film is a consumable item that wears over time.
What stands out
- Includes 2 FEP release films for the Photon Mono 2 and Mono 4
- Integrated ring design allows for quick installation in about 3 minutes
- No need to cut the film or disassemble the ring during setup
- Dimensions are 6.3 inches wide by 8.66 inches long
- Tutorial included on the package to guide the replacement process
Who it fits
Good fit for
You should buy this if you own a Photon Mono 2 or Mono 4 and need a straightforward replacement. The integrated ring design suits users who want to avoid the hassle of cutting FEP or handling loose films. It is also ideal for those who prefer a guided installation process with the included tutorial. If you value quick maintenance and do not require high-speed printing features, this 2-pack provides the necessary consumables to keep your printer running smoothly.
Who should skip it
Skip this product if you use a Photon Mono 4 Ultra or Mono 4 series printer and rely on fast printing modes. The data states this film does not support fast printing on those models. You would need to adjust your printing speed to normal rates to use it. If you cannot or will not slow down your print jobs, this film will not work for your setup. Look for a film explicitly rated for high-speed printing instead.
Verdict: This 2-pack offers a convenient, ring-integrated FEP solution for standard-speed printing on compatible Mono 2 and Mono 4 printers. It is a practical choice for users who prioritize easy installation over high-speed performance.
Key specs explained
Release Film Type: FEP
FEP is a fluoropolymer material known for its non-stick properties and chemical resistance. This means cured resin does not adhere strongly to the film, allowing you to peel prints off easily without damaging the model. It withstands exposure to liquid resin solvents better than standard plastics. You benefit from consistent print quality and reduced risk of film tears during the release phase of each layer.
Package contains 2 pcs
The listing provides two replacement films in a single purchase. Since FEP films are consumables that wear out over time, having a spare allows you to swap films quickly when one degrades. This minimizes printer downtime. You can keep one film installed while storing the second, ensuring you are always ready for maintenance. This is practical for users who print frequently and need to maintain a steady workflow.
Width: 6.3 inches
This dimension refers to the horizontal span of the release film. It is sized to fit the build platform of the Photon Mono 2 and Mono 4 printers. You do not need to trim the width if it matches your printer's vat dimensions. This ensures full coverage for your prints. When shopping, check that the width matches your specific printer model to avoid gaps or overhangs that could cause leaks.
Length: 8.66 inches
This measurement indicates the vertical length of the film. It is designed to wrap around the build platform of compatible Anycubic printers. The length must be sufficient to cover the entire build area without excessive overlap that could interfere with the z-axis movement. You benefit from a precise fit that maintains tension. Verify this length matches your printer's requirements to ensure proper installation and printing accuracy.
Height: 0.75 inches
This value likely refers to the thickness or a specific dimension of the film packaging or the film stack itself. In the context of consumables, it ensures the film fits within the tension ring mechanism of the printer vat. A consistent thickness helps maintain uniform pressure across the build surface. You should confirm this specification aligns with your printer's manual to ensure the film sits correctly in the vat assembly without binding.
Design and build specs
The listing describes these replacement films as an integrated design. This means the release film comes attached to a ring. You do not need to disassemble the ring or cut the FEP material yourself. The package includes a tutorial to guide you through the replacement process. According to the listing, the entire installation takes about three minutes. This quick swap helps you maintain print quality since FEP is a consumable that wears out over time. Regular replacement ensures better results for your resin models.
The physical dimensions are listed as 6.3 inches in width, 0.75 inches in height, and 8.66 inches in length. These measurements match the build platform of the Photon Mono 2 and Mono 4 printers. The film is made of FEP, a fluoropolymer known for its non-stick properties. This material allows cured resin to peel off easily without damaging your prints. It also offers chemical resistance against the liquid resin you use.
Note that while these films fit the Mono 4 Ultra, they do not support fast printing modes. If you use them on a Mono 4 series printer, you must adjust the printing speed to the recommended normal speed. This design choice ensures the film remains intact during longer or standard speed prints. The two-pack allows you to keep a spare ready for when the current film shows signs of wear or damage.
Setup and everyday use guide
Installing this FEP film is designed to be a quick process that takes about three minutes. Because the release film comes with an integrated ring, you do not need to disassemble the ring or cut the material yourself. The package includes a tutorial to help you replace the film correctly. This integrated design simplifies the setup, allowing you to focus on getting your printer ready for the next job without complex preparation steps. These films are compatible with the Anycubic Photon Mono 2 and Mono 4 series. They also fit the Mono 4 Ultra, but with an important limitation. The listing states that these films do not support fast printing models. If you use them on a Mono 4 series printer, you must adjust the printing speed to the recommended normal speed. Using them at higher speeds may not work as intended. As a consumable item, the FEP film will wear down over time. Regular replacement ensures that your prints continue to come off cleanly. The non-stick properties of the FEP material mean that cured resin does not adhere strongly to the film. This allows you to peel prints off easily without damaging the model. If you notice your print quality declining or if the film shows signs of wear, it is time for a replacement. Following the included tutorial helps you maintain consistent results. Proper maintenance of this consumable part is key to keeping your resin printing process smooth and reliable.
Before you buy this FEP film
You should keep a spare FEP film on hand because it is a consumable that wears out over time. Regular replacement ensures your prints maintain high quality and detail. This pack contains two films, which helps you stay prepared for future changes. Check your printer model before purchasing. These films are compatible with the Photon Mono 2 and Mono 4 series. They also work with the Mono 4 Ultra, but you must adjust your printing speed to normal levels. Do not use them for fast printing modes on that specific model. Follow the included tutorial for installation. This takes about three minutes. The integrated ring design simplifies the process. You do not need to cut the film or disassemble parts. Proper maintenance of this part supports the overall performance of your resin printer. It fits into your workflow as a necessary upkeep item. Having extras ready prevents downtime when the current film shows signs of wear or damage.
Check before you buy
- Verify your printer is a Mono 2 or Mono 4
- Check if you need normal speed for Mono 4 Ultra
- Confirm you have a spare film ready for replacement
- Review the included installation tutorial before starting
The product at a glance
ANYCUBIC Photon Mono 2 and 4 FEP Film 2-Pack
Best for: Anycubic Photon Mono 2 and Mono 4 users
- Release Film Type
- FEP
- Dimensions
- 8.66 × 6.3 × 0.75 inches
View on Amazon: ANYCUBIC Photon Mono 2 and 4 FEP Film 2-Pack Affiliate link
This is a replacement FEP film pack for Anycubic Photon Mono 2 and Mono 4 printers. It includes two films with a pre-installed ring for quick installation in about three minutes. The films measure 6.3 inches by 8.66 inches. You should adjust print speeds to normal if using these on Mono 4 series models for fast printing. Regular replacement helps maintain print quality.
Pros
- Includes two FEP films for extended use
- Pre-installed ring allows for quick 3-minute installation
- Compatible with Photon Mono 2 and Mono 4 series
Cons
- Requires normal print speed settings on Mono 4 series for fast printing models
- Consumable item needing regular replacement
- No mention of included tools beyond the ring
Good fit if
- You own an Anycubic Photon Mono 2 printer
- You want a quick replacement process with pre-installed rings
- You need backup films for regular maintenance
Skip if
- You use a printer model not listed as compatible
- You prefer films without pre-installed rings
- You need films for fast printing on Mono 4 Ultra without speed adjustment
Verdict: ANYCUBIC Photon Mono 2 FEP Film 2-Pack offers a convenient solution for users of Photon Mono 2 and Mono 4 printers who value quick installation. It is ideal for those who need reliable replacement films and do not mind adjusting print speeds for optimal results on Mono 4 series devices.
Specifications side by side
| Spec | ANYCUBIC Photon Mono 2 and 4 FEP Film 2-Pack |
|---|---|
| Release Film Type | FEP |
| Dimensions | 8.66 × 6.3 × 0.75 inches |
Frequently asked questions
Is this FEP film compatible with the Photon Mono 4?
Yes, the ANYCUBIC Photon Mono 2 and 4 FEP Film 2-Pack is designed for both Mono 2 and Mono 4 users. The dimensions match the build area requirements for these specific models. You can use this pack to replace worn films on either device without needing different sizes.
What are the exact dimensions of the FEP film?
The film measures 6.3 inches in width and 8.66 inches in length. The height of the material itself is 0.75 inches. These specific measurements ensure a proper fit for the resin tank screens found in the Photon Mono 2 and Mono 4 printers.
Does the package include the ring for installation?
Yes, the release film comes attached to a ring in an integrated design. You do not need to disassemble a separate ring or cut the FEP material yourself. This setup simplifies the replacement process, allowing for a quick installation that takes about three minutes.
How many FEP films are included in the pack?
The package contains two FEP films. This allows you to keep a spare on hand for future replacements. Since FEP is a consumable that wears out over time, having two films helps you maintain print quality without needing to order immediately after the first one degrades.
Is there a guide included for installation?
Yes, the package includes a tutorial to guide you through the installation process. This resource helps you install the integrated ring and film correctly. Following the guide ensures you avoid common mistakes and achieve a secure seal for optimal printing results.
What material is used for the release film?
The film is made from FEP, a fluoropolymer known for its non-stick properties. This material resists chemical exposure from resin, preventing strong adhesion of cured material. This allows you to peel prints off easily without damaging the model or the film itself.