ANYCUBIC 10.1-Inch ACF High-Speed Film Review: Specs, Pros and Cons

What stands out

• ACF release film type for improved layer separation
• Dimensions of 278x190mm fit M5s and M7 Pro printers
• 0.3mm thickness balances durability and flexibility
• Approximately 95% light transmittance for consistent curing
• Package includes five films for extended use

Who it fits

Key specs explained

Dimensions 278x190(mm)

This size matches the build area of the Photon Mono M5s, M5s Pro, and M7 Pro printers. You need this exact footprint to fit the resin vat properly. If the film is too small, you lose print area. If it is too large, it will not sit flat. Always verify the millimeter measurements against your printer manual before buying.

Film Thickness 0.3mm

The film is three-tenths of a millimeter thick. This specific thickness ensures proper separation from the cured resin layer. A thicker film might stick to the model. A thinner one might tear easily. This balance helps you achieve clean prints without damaging the bottom of your parts during the peeling process.

Release Film Type ACF

ACF stands for Anti-Adhesion Coating Film. This coating prevents the resin from bonding to the film itself. You can lift prints off easily without scraping. This reduces the risk of tearing the bottom of your model. Standard films lack this coating, making removal difficult. Choose ACF for smoother post-processing and better surface quality.

Light Transmittance about 95%

This film lets ninety-five percent of light pass through. High transmittance means the UV light reaches the resin quickly and evenly. This supports faster printing speeds. Lower quality films block more light, causing weak layers or incomplete cures. If you use high-speed resin, this high percentage ensures your prints cure fully in the intended time.

Material and Size Details

According to the listing, the film uses an ACF release film type. This material choice supports high-speed resin printing. The listing notes that you must pair it with Anycubic’s high-speed resin to achieve the intended fast print speeds. The film has a thickness of 0.3mm. This specific thickness helps maintain consistent layer adhesion during rapid curing cycles. The listing states the light transmittance is about 95%. High transmittance allows UV light to pass through efficiently. This reduces exposure time per layer. It helps prevent under-cured prints on the bottom layers.

The film dimensions are 278 by 190 millimeters. This size matches the build plate area of the Photon Mono M5s, M5s Pro, and M7 Pro. You need this exact footprint to fit the resin vat properly. The listing describes the film as a consumable item. Regular replacement maintains good printing performance. If the film deforms or damages during printing, you should replace it immediately. The package includes five pieces. This allows for multiple prints before needing a new supply. The listing advises removing the outer protective layer from the bottom release film before installation. This step is critical for proper adhesion and light transmission. Proper installation ensures the film stays flat and functional throughout the printing process.

Setup And Daily Use Guide

You install this film only on Anycubic Photon Mono M5s, M5s Pro, and M7 Pro printers. The listing states that the film is designed to work with Anycubic high-speed resin. You must pair it with this specific resin to achieve the fast printing speeds the product promises. The package contains five films. Each film measures 278 by 190 millimeters. The thickness is 0.3 millimeters. The light transmittance is about 95 percent. This high transmittance helps the UV light pass through efficiently during the curing process.

Before you install the new film, you need to remove the outer protective layer from the bottom of the resin vat. This step is critical for proper adhesion and print quality. You should check the film regularly during your printing sessions. The listing notes that this is a consumable item. You need to replace it regularly to maintain good printing performance. If the film becomes deformed or damaged while you are printing, you should replace it immediately. Do not continue using a damaged film. This will prevent defects in your prints.

If you have questions about the installation or use, you can contact the seller. The listing says you can get a reply within 12 hours. This support channel is available if you encounter issues during setup or daily operation. Keep spare films on hand since you will need them often. The film size matches the build volume of your printer. Ensure you handle the film carefully to avoid scratches before installation. Proper setup leads to better results.

Before You Buy This Film

You need to verify your printer model before ordering. This film fits only the Photon Mono M5s, M5s Pro, and M7 Pro. Check your device name in the settings menu. You must also buy compatible high-speed resin. The listing specifies that standard resin will not work with this film for fast printing. You are buying a consumable part. Replace the film when it shows scratches or deformation. Keep extra packs in your supply kit. This item sits alongside other printer accessories in the 3D Printers & Making Tools category. It does not replace the printer itself. You need the machine, the resin, and this film to print. Remove the protective layer on the bottom of the release film before installing. This step is critical for proper adhesion. Do not skip it. The package includes five films. This allows for several replacements over time. Store unused films in a cool, dry place. Dust can ruin the surface. Handle the film by the edges only. Your prints depend on this thin layer. Treat it with care.

Check before you buy

• Confirm your printer is a Photon Mono M5s, M5s Pro, or M7 Pro.
• Purchase Anycubic high-speed resin for compatible fast printing performance.
• Remove the outer protective layer from the film bottom before installation.
• Check for scratches or deformation on the current film before replacing.

The product at a glance

1

Anycubic 10.1-Inch ACF High-Speed Film

Best for: Anycubic M5s and M7 Pro owners

Dimensions

278x190(mm)

Release Film Type

ACF

Film Thickness

0.3mm

Printing Technology

Resin

Features

High Speed

Resolution

12K, 14K

View on Amazon: Anycubic 10.1-Inch ACF High-Speed Film Affiliate link

This package contains five Anycubic 10.1-inch ACF release films for resin printers. The films measure 278x190 mm with a 0.3 mm thickness and 95% light transmittance. They are designed for the Photon Mono M5s, M5s Pro, and M7 Pro models. You should use these with Anycubic high-speed resin. Regular replacement maintains print quality. This is a consumable part for compatible machines.

Pros

• Includes 5 films per package
• 95% light transmittance
• 0.3 mm film thickness
• Specifically for Anycubic high-speed resin

Cons

• Only works with Anycubic Photon Mono M5s, M5s Pro, and M7 Pro
• Requires removal of protective layer before use
• Must be replaced if deformed or damaged

Good fit if

• You own an Anycubic Photon Mono M5s or M5s Pro
• You own an Anycubic Photon Mono M7 Pro
• You use Anycubic high-speed resin

Skip if

• You use a printer brand other than Anycubic
• You need films for 13.6-inch models
• You prefer a single film purchase

Verdict: Anycubic 10.1-Inch ACF Film is a direct replacement part for owners of the Photon Mono M5s, M5s Pro, or M7 Pro. It ensures proper light transmission for fast resin printing when used with the correct software and resin settings.

Specifications side by side

Frequently asked questions

See also

• anycubic 5pcs 10 1 inch acf high alternatives
• anycubic 5pcs 10 1 inch acf high vs printhead assembly 3d printer
• venluna 10 1 inch 4k touch review
• seesii 10 inch 2 in 1 cordless pole review